EE2356 MICROPROCESSOR AND MICRO CONTROLLER LABORATORY Syllabus EEE Sixth(6th) Semester - Anna University - Regulation 2008


EE2356 MICROPROCESSOR AND MICRO CONTROLLER LABORATORY  L T P C
                                                                                                                             0 0 3 2
AIM
1. To understand programming using instruction sets of processors.
2. To study various digital & linear 8-bit Microprocessor
1. Simple arithmetic operations: Multi precision addition / subtraction / multiplication / division.
2. Programming with control instructions: Increment / Decrement, Ascending / Descending
order, Maximum / Minimum of numbers,Rotate instructions
Hex / ASCII / BCD code conversions.
3. Interface Experiments:
A/D Interfacing.
D/A Interfacing.
Traffic light controller.
4. Interface Experiments:
Simple experiments using 8251, 8279, 8254.
8-bit Microcontroller
5. Demonstration of basic instructions with 8051 Micro controller execution, including:
Conditional jumps, looping
Calling subroutines.
Stack parameter testing
6. Parallel port programming with 8051 using port 1 facility:
Stepper motor and D / A converter.
7. Study of Basic Digital IC’s
(Verification of truth table for AND, OR, EXOR, NOT, NOR, NAND, JK FF, RS FF,D FF)
8. Implementation of Boolean Functions, Adder / Subtractor circuits.
9. Combination Logic; Adder, Subtractor, Code converters, Encoder and Decoder,
10. Sequential Logic; Study of Flip-Flop, Counters )synchronous and asynchronous), Shift
Registers
11. Op-Amp Linear Application: Comparator, Differentiator, Integrator, Adder, Subtractor.
12. Op-amp Non Linear Application; Clipper, Clamper, Peak detector, Timer IC application, VCO and PLL.
TOTAL : 45 PERIODS
73
REQUIREMENT FOR A BATCH OF 30 STUDENTS
S.No. Description of Equipment IC
number/code
Quantity
required
1. 8085 Microprocessor Trainer with
Power supply
- 15
2. 8051 Micro controller Trainer Kit with
power supply
- 15
3. 8255 Interface board - 5
4. 8251 Interface board - 5
5. 8259 Interface board - 5
6. 8279 Keyboard/Display Interface Board - 5
7. 8254 timer counter - 5
8. ADC and DAC card - 5
9. Stepper motor with Controller - 5
10. Traffic Light Control System - 5
11. Regulation power supply - 30
12. Universal ADD-ON modules - 5
13. 8 Digit Multiplexed Display Card - 5
14. Function Generator - 10
15. Multimeter - 20
16. C R O - 10
17. Quad 2-input AND gate 7408 50
18. Quad 2-input OR gate 7432 50
19. Quad 2-input XOR gate 7486 50
20. Hex inverter/ NOT gate 7404 50
21 Quad 2-input NOR gate 7402 50
22. Quad 2-input NAND gate 7400 50
74
23. Dual J-K flip Flop with clear 7473 50
24. Dual D flip Flop with clear / preset 7474 50
25. 4 – bit Adder 7483 50
26. 4- bit Magnitude comparator 7485 50
27. BCD to 7-segment code converter 7447 50
28. 3 to 8 Decoder / Demultiplexer 74138 50
29. Decade / Modulo- n counter 7490 50
30. 4 – bit serial / parallel in/out shift
register
7495 50
31. General purpose OPAMP 741 100
32. Timer 555 100
33. Voltage Controlled Oscillator (VCO) 566 25
34. Phase Locked Loop (PLL) 565 25
35. Diode IN4007 25
36. Zener diode 5 volt 25
37. Light Emitting Diode (LED) LED 25
38. Resistors (quarter watt) : 10K, 33k ohm - 50 each
39. Capacitors : 0, 1uF, 0.01uF, 0.47uF - 50 each
40. Bread Board - 30
41. Single strand wire - 10 packet
42. Wire stripper - 10
Previous
Next Post »